CM106B 为可调节高度的三脚塔,镀锌管材质;它替代了CM106,更容易设置和使用。类似CM106,CM106B可在7 到10英尺范围内调节,所以它替代了6英尺的CM6 和10英尺的CM10。而且重量更轻,因为CM106/B由薄钢管组成,而CM6/10由标准厚度的钢管组成。CM106B 为通用目的的三脚塔,可固定传感器、太阳能板、天线和设备防护机箱。
The CM106B is constructed with individually adjusted legs that allow installation over uneven terrain. Height of the mast is 2.1 m (7 ft), or 3 m (10 ft) with the mast extended.
The CM106B includes lightning and grounding rods, grounding cables, UV resistant cable ties, and stakes for securing the tripod feet to the ground. An optional guy kit is recommended for sites that may experience high wind speeds. (See Allowable Wind Speeds in the Specifications.) Instrument enclosures can be purchased with mounting brackets that attach to either the mast or leg base.
The CM106B can be used for a variety of applications. For meteorological stations, sensors are mounted to the tripod using mounting brackets appropriate for the model of sensor. For nonmeteorological applications, the tripod can be used to mount instrument enclosures, solar panels, junction boxes, or antennas.
Vertical Load Limit | 200 kg (440 lb) |
Leveling Adjustment | Slide collars on each leg adjust individually. |
Maximum Slope Angle | 45° or 100% grade |
Measurement Height |
|
Leg Base | 11.43 x 13.97 cm (4.5 x 5.5 in.) with four 1.58 cm (0.62 in.) holes for stakes |
Collapsed Diameter | 20.3 cm (8 in.) |
Collapsed Length | 1.83 m (6 ft) |
Main Lower Mast Outer Diameter | 48 mm (1.90 in.) |
Retractable Upper Mast Outer Diameter | 44 mm (1.74 in.) |
Base Diameter | 2.7 to 3.5 m (8.7 to 11.5 ft) |
Weight | 24.5 kg (54 lb) with mast |
Maximum Allowable Sustained Wind |
|
-NOTE- |
Allowable sustained wind and wind gust values assume the following:
|
Mast Extended |
|
Mast Retracted |
|
Maximum Allowable Wind Gust |
|
-NOTE- |
Allowable sustained wind and wind gust values assume the following:
|
Mast Extended |
|
Mast Retracted |
|
Please note: The following shows notable compatibility information. It is not a comprehensive list of all compatible products.
Product | Compatible | Note |
---|---|---|
019ALU (retired) | ||
CM202 | ||
CM202SS | ||
CM203 | ||
CM204 | ||
CM204SS | ||
CM206 | ||
UT018-5 (retired) |
The “-MM” mount option for our environmental enclosures is intended for mounting the enclosure to a tripod's mast. An enclosure ordered with this option will be shipped with a three-piece bracket mounted to the top of the enclosure and an identical three-piece bracket mounted to the bottom of the enclosure.
All of our standard enclosures (including the ENC16/18) can be mounted to the CM106's leg base. The "-LM" mount option for our environmental enclosures allows the enclosure to be attached to the leg base of the CM106. This option includes a metal flange, two brackets, and a 2.5" u-bolt. The brackets attach to the right and left side of the enclosure, and the flange attaches to the tripod near the mast. The flange fits into a notch in one of the brackets, and the other bracket connects to a tripod leg via the u-bolt.
CM106B: 1
To provide additional support for the mast in areas that experience high wind speeds, order the optional guy kit for the CM106B (pn 29813). Refer to the Specifications information on the CM106B product page, which describes a guy kit’s effect on the “Maximum Allowable Sustained Wind” and the “Maximum Allowable Wind Gust” of a CM106B.