Rotation of the A100LK’s three-cup rotor is electronically converted to pulse output signals proportional to wind speed. The A100LK produces a higher rate of pulses per revolution (up to 13) compared to relay-based sensors, making it suitable for wind surveying where turbulence needs to be estimated.
Sensor | 3-cup anemometer |
Measurement Description | Wind speed |
Signal Type/Output | Electronic pulse |
Range | 0 to 77 ms-1 |
Threshold | 0.15 ms-1 (starting speed 0.2 ms-1, stopping speed 0.1 ms-1) |
Maximum Speed | 77.22 ms-1 |
Accuracy | 1% ±0.1 ms-1 |
Distance Constant | 2.3 m ±10% |
Calibration Data |
Supplied for anemometer and rotor at one test speed to an accuracy of ±1% at +15°C. (12 Vdc supply and an analog output load of 1 MΩ) |
Operating Temperature Range | -30° to +70°C |
Rotor | 15.2 cm (6 in.) diameter three-cup rotor |
Supply Voltage | 6.5 to 28 Vdc |
Current Consumption |
2 mA maximum 1.6 mA typical (no output load) |
Power-up Time | 5 s |
Surge Protection | Vector PC3L2 anti-surge module fitted |
Housing Diameter | 5.5 cm (2.2 in.) |
Height | 19.5 cm (7.68 in.) |
Weight | 490 g (17.3 oz) including 3 m (10 ft) cable |
Please note: The following shows notable compatibility information. It is not a comprehensive list of all compatible products.
Product | Compatible | Note |
---|---|---|
CR1000X (retired) | ||
CR300 (retired) | ||
CR3000 (retired) | ||
CR310 | ||
CR350 | ||
CR6 | ||
CR800 (retired) | ||
CR850 (retired) |
The A100LK uses one pulse count channel on the data logger.
The A100LK is read by the PulseCount Instruction in CRBasic and by Instruction 3 (Pulse Count) in Edlog. Wind speed measurements can be taken and processed with any of the data loggers.
A100LK-L: 6
展开全部收起全部
No. Cables are attached and sealed on the sensor by the manufacturer. Whenever possible, purchase a sensor with the desired cable length. Alternatively, a new sensor can be purchased with a foot of cable and then spliced onto the existing cable. Splicing cable together, however, increases the likelihood that water may enter the cable and cause shorting, corrosion, and some other potential issues, which in turn can cause measurement issues. Because of the potential issues, do not splice any sensor cable without first contacting Campbell Scientific to discuss the sensor in detail.
Yes. Every A100LK-L ships with a MEASNET calibration certificate.
大多数 Campbell Scientific 传感器的型号中都带有 –L,它表示用户指定线缆长度。如果传感器型号名称列有 –LX (这里 “X” 是其它的某个字符), 那么该传感器需要用户指定长度,但线缆尾端会配有用于某个独特系统的特殊快速接头:
如果一个传感器的主型号数字的后面没有被指定 –L 或其它的 –LX 字符,那么该传感器将具有固定的线缆长度。在产品页面订购栏中 (Ordering tab) 的描述字段的末尾,会列出线缆的长度。例如 034B-ET 型号的描述字段含有信息:Met One风传感器适用于ET气象站,67英寸线缆 (Met One Wind Set for ET Station, 67 inch Cable)。产品按固定的线缆长度做尾端处理,默认是尾线方式。
如果线缆尾端配有用于某个独特系统的特殊快速接头,则型号尾部的字符会指定该传感器用于哪一个系统。例如,034B-ET 型号表明该传感器是一个 034B 且用于 ET107 系统。
不是每一种传感器都有不同的线缆尾端选项。通过查找传感器产品页面的订购栏 (Ordering tab) 中的两个位置,可以检查某种特定传感器的可用的线缆尾端选项:
如果传感器以 –ET, –ETM, –LC, –LQ, 或 –QD 等版本的型号供应,那么线缆尾端选项已经反映在该传感器的产品型号中。例如,034B 以 034B-ET, 034B-ETM, 034B-LC, 034B-LQ, 和 034B-QD 等型号供应。
所有其它的线缆尾端选项,如果可用,会列在该传感器产品页面的订购栏 (Ordering tab) 中的线缆尾端选项 (“Cable Termination Options) 区域。例如,034B-L 风速风向传感器具有 –CWS, –PT, 和 –PW 等线缆尾端选项,显示在 034B-L 产品页面的 订购栏 (Ordering tab) 位置。
注: 当更新的产品添加到我们的库存中时,一般来说,我们会在单个传感器的产品型号下面列出多种线缆尾端选项,而不是创建多个产品型号。例如,HC2S3-L 具有 –C 线缆尾端选项用于连接到 CS110,而我们并没有使用 HC2S3-LC 产品型号。
Campbell Scientific 的很多传感器都有可行的不同线缆尾端处理选项,包括以下几种:
注: 线缆尾端选项的可行性因传感器而异。例如,传感器可能会有 无选项、两个选项或几个选项可供选择。如果预期的选项没有列在所指定的传感器中,请联系 Campbell Scientific 的应用工程师寻求帮助。
It is possible that an older version of Short Cut is being used. Download the latest version of Short Cut.
If the latest version of Short Cut has already been downloaded, open the program.