为您的数据采集器提供长期的、无故障的保护
概览
作为CS110闪电预警系统的一部分，FC100设计用于SG000 Strike Guard闪电探测器。SG000通过光纤线缆输出自己的数据信号，FC100安装在光纤的末端和数据采集器前面。FC100将光纤信号转换成RS-232信号，因而在传感器和数据采集器之间具备了闪电防护连接功能。
FC100还可用作两个串口设备之间（数据采集器到PC）的RS-232连接，相隔距离小于100 m。FC100为DCE设备，因而在它与数据采集器之间需要一根空modem线缆。
优势与特点
- 防雷的安全串行通讯
- 坚实耐用的设计，适合长期无故障的操作
- 瞬时端子，不需要接头、压线、抛光或环氧树脂
图像
技术说明
作为CS110闪电预警系统的一部分，FC100设计用于SG000 Strike Guard闪电探测器。SG000通过光纤线缆输出自己的数据信号，FC100安装在光纤的末端和数据采集器前面。FC100将光纤信号转换成RS-232信号，因而在传感器和数据采集器之间具备了闪电防护连接功能。
FC100还可用作两个串口设备之间（数据采集器到PC）的RS-232连接，相隔距离小于100 m。FC100为DCE设备，因而在它与数据采集器之间需要一根空modem线缆。
产品规格
| Electrical Connector | 9-pin, D sub, DTE compatible |
| Baud Rates | 1,200 to 19,200 bps (at 100 m guaranteed with FC100CBL-L cable) |
| Power | 12 Vdc (via pn 14291 or pn 15966) |
| Current | 5 mA (average) |
| Mounting Holes | 7.62 cm (3 in.) apart |
| Case Width | 2.8 cm (1.1 in.) |
| Dimensions |
|
兼容性
Please note: The following shows notable compatibility information. It is not a comprehensive list of all compatible products.
数据采集器
| Product | Compatible | Note |
|---|---|---|
| CR1000X (retired) | ||
| CR200X (retired) | ||
| CR206X (retired) | ||
| CR211X (retired) | ||
| CR216X (retired) | ||
| CR295X (retired) | ||
| CR300 (retired) | ||
| CR3000 (retired) | ||
| CR310 | ||
| CR350 | ||
| CR5000 (retired) | ||
| CR6 | ||
| CR800 (retired) | ||
| CR850 (retired) |
Additional Compatibility Information
The FC100 is used with the SG000 Strike Guard.
常见问题解答
FC100: 10
展开全部收起全部
-
Short-fiber runs sometimes pass too much signal. The solution is to pull the fiber part way out of the holding ferrule.
-
With a good signal strength, 1200 to 19,200 bps.
-
The 12 Vdc power supply keeps the signal from dropping when large data packets are transmitted.
-
100 m (330 ft) with a 1.0 mm poly-methylmethacrylate (PMMA) core with a PVC or polyethylene jacket, simplex or duplex; up to 1 km with a higher-grade fiber.
-
The data transmission fibers are fragile and cannot be bent or broken. Consequently, the fibers need to be handled with care and protected inside a conduit (usually PVC).
-
They provide lightning-proof and lightning-safe serial communication that eliminates the need for transient suppression devices.
-
Direct communication between two RS-232 serial devices, such as a PC to a data logger or a data logger to a serial sensor.
-
The FC100 provides instant termination—no connectors, crimping, polishing, or epoxy.
-
The FC100 is required to communicate with the SG000 Strike Guard Lightning Sensor. The SG000 is an option for the CS110 Electric Field Sensor and the LW110 Lightning Warning System.
-
The FC100 is designed for lightning-proof and lightning-safe serial communication. Because the FC100 offers PMMA or glass fibers that are not conductive, electrical surges (such as those caused by lightning) cannot travel between the modems.