停产的 ›
这个产品是无效的且被替换: CR300,CR310.
CR216X 带2.4-GHz电台的数据采集器
Services Available
Repair Yes
Calibration No
Free Support Yes

概览

>CR216X是我们最小巧的成本最低的数据采集器,内置有 2.4 GHz射频电台,可将数据发送到另一个CR216(X)、RF416电台或RF432电台。2.4 GHz频段适用于全世界。

CR216X能在严酷的远程环境中独立工作。通过输入端口读取一个或两个传感器,再使用内置电台以无线方式向外传输数据。多个CR216X可以被设置成数据采集器网络;或者,众多CR216X单元也可被逐个配置。

优势与特点

  • Small, low-cost data logger with internal spread spectrum radio for wireless communications
  • Integrated radio lets this data logger function like a wireless sensor in a network, transmitting to a master data logger
  • Ideal applications include wind energy, rural water, water level/flow, aquaculture, water quality
  • Gas Discharge Tube (GDT) protected inputs
  • Optimal for measuring one or two simple sensors
  • Makes SDI-12, single-ended analog, pulse, switch closure, and bridge measurements
  • Battery-backed clock that ensures accurate time is maintained while data logger is disconnected from battery power
  • Program with LoggerNet, PC400, or Short Cut to fit your setup
  • PakBus, Modbus, and SDI-12 protocols supported

图像

技术说明

CR216X可用于无线传感器网络应用中。其具有吸引力,是因为比起挖沟、埋管、穿线起来,无线传感器网络经常更经济一些。此时,CR216X测量所连接的传感器,再把数据通过自己的射频电台无线地发送到主数据采集器上。主数据采集器必须支持PakBus通讯协议(例如:CR800、CR850、CR1000、CR3000)。查找如何关于如何设置PakBus系统的更多信息,请阅读我们的PakBus网络系统指导。

CR216X具有几个输入通道,可以测量一系列的传感器。气体放电管为输入通道提供了坚固耐用的电子放电保护功能。

CR216X不可以作差分测量,也不支持SDM设备、扩展板或热电偶(参阅兼容性标签查找可兼容的传感器、外设和软件)。没有提供给CR216X数据采集器的再校准服务。

产品规格

-NOTE- Note: Additional specifications are listed in the CR200X-Series Specifications Sheet.
Internal Spread-Spectrum Radio Operating Frequency Range 2.450 to 2.482 GHz
Transmitter Power Output 50 mW
Maximum Scan Rate 1 Hz
Analog Channels
  • The single-ended analog inputs can also be used as control ports.
  • 5 single-ended (no differential) individually configured
Pulse Count Channels 2
Switched Excitation Channels 2 voltage
Digital Ports
  • Certain digital ports can be used to count switch closures.
  • 2 I/O
Communication Ports 1 RS-232
Switched Battery Port 1
Input Voltage Range 0 to 2500 mV
Analog Voltage Accuracy ±(0.25% of reading + (1.2 mV)x(offset)) at -40° to +50°C
Analog Voltage Resolution 0.6 mV
A/D Bits 12
Operating Temperature -40° to +50°C
Power Requirements 7 to 16 Vdc
Typical Current Drain
  • ~0.2 mA (quiescent)
  • ~3 mA (active, no radio)
  • ~36 mA (active, radio receive)
  • ~75 mA (active, radio transmit)
Protocols Supported PakBus (leaf node only), SDI-12
CE Compliance Standards to which Conformity Is Declared IEC61326:2002
Warranty 3 years
Dimensions 14.0 x 7.6 x 4.8 cm (5.5 x 3.0 x 1.9 in.)
Weight 271 g (9.5 oz)

Memory

Final Storage 512 kB of flash memory for approximately 125,000 data points
Operating System 106 kB of flash memory
Intermediate Storage 8 kB of SRAM for communication buffers, calculations, variables, etc.

兼容性

Please note: The following shows notable compatibility information. It is not a comprehensive list of all compatible products.

传感器

Product Compatible Note
014A-L
03002-L
03101-L
034B-L
05103-45-L (retired)
05103-L
05106-L (retired)
05305-L
083E-L (retired)
092-L (retired)
107
108
109
109SS-L
110PV-L (retired)
237-L (retired)
255-100
27106T-L
43347-L
52202-L
A100LK-L
CMP11-L (retired)
CMP21-L
CMP6-L (retired)
CS100
CS106
CS11-L
CS215-L (retired)
CS300-L (retired)
CS410-L (retired)
CS451
CS456
CS460-L (retired)
CS470 (retired)
CS471 (retired)
CS475A-L
CS475-L (retired)
CS511-L
CS526-L (retired)
CS547A-L
CS616
CS625 (retired)
CS650
CS655
CS700-L
CSAT3 (retired)
CSIM11-L
CSIM11-ORP-L
ENVIROSCAN (retired)
HC2S3-L (retired)
HMP155A-L
HMP60-L
LI190SB-L (retired)
LI200X-L (retired)
LWS-L
OBS500 (retired)
OBS501 (retired)
P2546A-L
SEN12512 (retired)
SR50A-L (retired)
TB4-L
TB4MM-L
TE525-L
TE525MM-L
TE525WS-L
WINDSONIC1-L
WINDSONIC4-L
WXT520 (retired)

软件

Product Compatible Note
LoggerNet Version 2.1 or higher
PC200W (retired)
PC400 Version 1.0 or higher
PCONNECT (retired)
PCONNECTCE (retired) Version 2.0 or higher
Short Cut
VISUALWEATHER Version 2 or higher

Additional Compatibility Information

Communications

The CR216X can communicate with a PC via direct connect, NL201 Network Link Interface, NL240 Wi-Fi Network Link, MD485 multidrop modem, and digital cellular modems. Data can be viewed on an iOS device, an Android device, CD295 DataView II Display, or a user-supplied PDA. To use an iOS or Android device, go to the Apple Store or Google Play and download our LoggerLink Mobile Apps free of charge. User-supplied PDAs require either PConnect or PConnectCE software.

The CR216X's internal spread spectrum radio can transmit data to other CR216(X) loggers, RF416 radios, or RF430 radios. Certain CR216X settings must match the radio's settings for communications between the data logger and radio to be successful. The factory default settings of these devices might not match; therefore, they may need to be reconfigured before communications can take place.

If the CR216X is in the transparent mode, it can communicate with the retired CR215 loggers or RF415 radios.

Measurement & Control Peripherals

Campbell Scientific’s SDM devices and multiplexers are not supported.

Sensors

The CR216X can measure a variety of sensors including SDI-12 sensors and 4 to 20 mA sensors. It cannot make differential measurements and is not compatible with the freezing-rain/ice, fuel moisture/temperature, geographic position, present weather, soil heat flux, soil matric water potential, and strain sensors listed on our price lists.

Enclosures

Applications with minimal power requirements can use the ENC200 enclosure to house the data logger and the #16869 sealed rechargeable battery. The ENC200 cannot house a barometer or a battery that is larger than the #16869. However, an ENC10/12 or ENC12/14 enclosure is adequate for most CR216X-based systems.

Power Supplies

The CR216X uses an external power supply and has a built-in regulator. When connected to the on-board charging circuit, the sealed rechargeable battery should be 7 A h or smaller. Using larger batteries with the data logger's built-in charger may result in excessive PC board heating. This is especially a concern when the battery is deeply discharged or failing with a shorted cell. Campbell Scientific also recommends that solar panels be 10 W or less and wall chargers be 1 A or smaller.

下载

CR200X Series OS v.04 (1.29 MB) 22-09-2015

Execution of this download installs the Operating System and Compiler on your computer for the following dataloggers:CR200X, CR206X, CR211X, CR216X and CR295X.  It also updates the support files for the CRBasic Editor.  

Note: Newer CR206X dataloggers (serial # ≥ 19122) and newer CR211X dataloggers (serial # ≥ 19143) have 250 mW radios that must use OS 3 or higher for their datalogger operating system.

查看修订历史

常见问题解答

CR216X: 39

展开全部收起全部

  1. Yes. The simplest method is to use conditional program statements that execute most of the code based on time. For example, the data could be scheduled to log at 6 a.m. and finish at 8 p.m. using CRBasic instructions such as IfTime(). Another option is to use an IfThen/EndIf construction that does a logical test of light-level measurements based on a light sensor. An additional option is to use calculated sunrise and sunset times along with a combination of RealTime() and Case instructions.

    For more information, see the “Decisions, Decisions, Decisions…” article. 

  2. If small amounts of data are transferred per transmission, it will not be a problem. Larger amounts of data can overrun buffers in the modem, causing lost data. In that situation, lower the baud rate on the data logger to avoid the issue.

  3. The CRBasic Editor Help contains example program code for all instructions in the data logger. Look for the Example link at the top of each instruction topic. The CRBasic Help Tutorial demonstrates how to access this and other online CRBasic Editor Help files.

    Also, many programming examples can be found in the data logger and sensor manuals that are available on the Campbell Scientific website.

  4. Technically, the SRM-5A is compatible with the CR200X-series dataloggers, but it is more complicated to use it with these data loggers. To use a SRM-5A with a CR200X-series datalogger, the SRM-5A must be in the DTE position on the station modem. In addition, user-supplied adapters and gender changers are needed to complete the connections between the SRM-5A and the RS-232 port of the data logger. Contact Campbell Scientific for more information.

  5. Yes, but only with a direct connection, such as an RS-232 cable or a USB-to-serial adapter. While connected to the data logger, press the Send Program button on the Clock\Program tab, and browse to the program file. 

  6. Current data loggers compatible with the BMP5 Direct SDK are the CR200X-series, CR1000, CR3000, CR800, and CR850.

    Retired compatible data loggers include the CR10X-PB, CR23X-PB, and CR510-PB. These data loggers must have the optional PakBus operating system installed, which is available on the Downloads page of our website.

  7. Not directly. If the CS15-L is connected to a CR200(X) datalogger, the data logger can take the ac measurement and control a solid-state relay based on some threshold within the data logger program. The solid-state relay can then control other relays, solenoids, or motor starters. (Use of a solid-state relay is preferred because the data logger can trigger it with a small 5 Vdc mA signal.) For more information, see the “Measurement and Control Peripherals” section of the operator’s manual.

  8. A data logger can be programmed to initiate data transfer by using the SendVariables() or ModemCallback() instruction in CRBasic. 

    NOTE: These instructions are not supported in the CR200X operating system.

  9. This might happen because the data logger clock is being adjusted by a remote time source. If this occurs close to the same time that the data logger is due to store data, it can result in either a skipped record or an additional record of data.

    If LoggerNet 4 is used to collect data on a schedule, check the setup for that data logger. Look at the settings on the Clock tab in the LoggerNet Setup Screen. If that is enabled, the clock is checked and set at midnight every day and may interfere with data collection at that same time.

    Skipped scans and power outages could also result in records missing from a data table. Check the data logger’s station status or Status table and look for skipped scans, watchdogs, and low 12 V counts.

  10. One of the simpler ways to approximate how long it will take for a data table to fill up is to open the LoggerNet Connect screen, click the Station Status button, and view the Table Fill Times tab.

    Note: Table Fill Time statistics cannot be calculated for a CR200-series datalogger.