PConnectCE 软件支持PocketPC 或Windows Mobile操作系统的PDA 与坎贝尔数据采集器之间的通讯。它可让您携带您的PDA与线缆,而不是笔记本电脑,连接您的数据采集器并下载数据。
PConnectCE 能用于从数据采集器下载数据,和转换数据到办公室计算机。所下载的数据在HotSync过程中转移到计算机上。这种过程也同步PDA与计算机之间的程序文件。
PConnectCE所支持的功能包括:
DCE/DTE 信息
PConnectCE 发货时所附带的接头和线缆,假设PDA充当DCE设备(数据通讯设备),带9-针D形母头接口。有些PDA充当DTE设备(数据终端设备),带9-针D形公头接口。如果是这种情况,要与CS I/O端口通讯,您将最可能使用SC32B(单独订购),替代附带在软件中的PDA-to-CS I/O接头;如果是与数据采集器的RS-232端口通讯,PDA的串口线缆可直接连接到数据采集器的RS-232端口(或者使用标准的串口线缆,如果要求使用延长线缆)。对于这种一般规则,不过也可能存在例外情况。如果有关于您的手持设备的RS-232功能的问题,请联系设备制造商。
Current Version | Version 2.33 began shipping in May 2008. |
Software Requirements |
|
PDA Operating System | Microsoft Pocket PC or Windows Mobile |
Computer Requirements | Windows-based, 32-bit operating system (Windows 95, 98, ME, NT, or XP; not designed for Windows 7 and might not work with that OS) |
Operating Temperature | -25° to +50°C |
CE Compliance | CE Compliant |
PDA to RS-232 Cable Length | 38.0 cm (15.0 in.) |
PDA to RS-232 Cable Weight | 75 g (2.6 oz) |
PDA to CS I/O Connector Dimensions | 2.3 x 4.1 x 7.6 cm (0.9 x 1.6 x 3.0 in.) |
PDA to CS I/O Connector Weight | 41 g (1.6 oz) |
Please note: The following shows notable compatibility information. It is not a comprehensive list of all compatible products.
Product | Compatible | Note |
---|---|---|
21X (retired) | ||
CR10 (retired) | ||
CR10X (retired) | For the CR510, CR10X, and CR23X, support for both the mixed-array and PakBus® data logger operating systems is provided in PConnectCE version 2.0 or higher; prior versions only supported the mixed-array OS. | |
CR200X (retired) | The CR200X-series and CR1000 dataloggers require PConnectCE version 2.0 or higher. | |
CR206X (retired) | The CR200X-series and CR1000 dataloggers require PConnectCE version 2.0 or higher. | |
CR211X (retired) | The CR200X-series and CR1000 dataloggers require PConnectCE version 2.0 or higher. | |
CR216X (retired) | The CR200X-series and CR1000 dataloggers require PConnectCE version 2.0 or higher. | |
CR23X (retired) | For the CR510, CR10X, and CR23X, support for both the mixed-array and PakBus® data logger operating systems is provided in PConnectCE version 2.0 or higher; prior versions only supported the mixed-array OS. | |
CR295X (retired) | The CR200X-series and CR1000 dataloggers require PConnectCE version 2.0 or higher. | |
CR3000 (retired) | The CR3000 requires PConnectCE version 2.1 or higher. | |
CR500 (retired) | ||
CR5000 (retired) | ||
CR510 (retired) | For the CR510, CR10X, and CR23X, support for both the mixed-array and PakBus® data logger operating systems is provided in PConnectCE version 2.0 or higher; prior versions only supported the mixed-array OS. | |
CR800 | The CR800 and CR850 require PConnectCE version 2.2 or higher. | |
CR850 | The CR800 and CR850 require PConnectCE version 2.2 or higher. | |
CR9000 (retired) |
--OR--
PDA-to-serial cable or cradle (one end of the cable/cradle must terminate in a 9-pin serial connector) is required. The cable/cradle connects to the PDA-to-CS I/O connector or PDA-to-RS232 cable via the 9-pin serial connector. This cable/cradle may be included with the PDA, or it may need to be purchased as a separate accessory from the PDA manufacturer or a third party supplier.
Third-party Bluetooth serial adapter is required. The interface and/or cables that are used to connect the adapter to the data logger will vary, depending upon whether the device acts like a DTE (computer) device or DCE (PDA) device. In some instances, this is evident by the pin-out of the adapter, but not always. A general rule is if the adapter has a 9-pin female connector, then the adapter is connected to the data logger using the PDA-to-CS I/O connector for the CS I/O port or the PDA-to-RS232 cable for the RS-232 port. If the adapter has a 9-pin male connector, then the adapter is connected to the data logger using an SC32B for the CS I/O port or it can be connected directly to the RS-232 port.
PConnectCE runs on Windows-based, 32-bit operating system (Windows 95, 98, ME, NT, or XP).
Upgrade PConnectCE 2.0, 2.1 or 2.2 to 2.33.
PConnectCE 2.0, 2.1 or 2.2 must be installed on your machine.
PCONNECTCE: 13
展开全部收起全部
Yes. The value of an input location or Public variable can be changed from the Measurements tab.
No. PConnectCE is compatible with direct serial communications (COM1─COM8), Infrared, Bluetooth, and point-to-multipoint RF401 radio communications in a Transparent RF network. For more information, refer to the “Connecting Your Pocket PC Handheld to the Datalogger” section of the instruction manual.
PConnectCE is installed on the PC. When the hot sync process is used with the Windows Mobile device, PConnectCE is transferred to the device. For more information, refer to the instruction manual.
On the PDA, select Start | Programs | PConnectCE.
Use PConnect software for Palm devices or PConnectCE software for Windows Mobile devices.