| Services Available | |
|---|---|
| Repair | No |
| Calibration | Yes |
| Free Support | No |
HMP45C 是一咱坚实耐用的精确的空气温度/相对湿度探头,它测量0 到 100% RH范围内的相对湿度,和-40° to +60°C范围内的温度。这种探头适用于长期的无人值守的监测应用,与所有的坎贝尔数据采集器都兼容。
HMP45C 使用HUMICAP电容型薄膜多聚物传感器来测量相对湿度,和一个PRT传感器来测量温度。建议每年对HMP45C重校准一次
为了减小功耗,可以仅在测量期间给HMP45C供电,此时可应用数据采集器的开关12 V端子。对于没有开关12 V端子的数据采集器,例如CR510 或 CR7,可使用SW12V 开关12 V模块来切换控制HMP45C传感器的供电。
| Supply Voltage | 12 Vdc nominal (typically powered by data logger) |
| Current Drain | ≤ 4 mA (active) |
| Cable Diameter | 0.8 cm (0.3 in.) |
| Sensor Diameter | 2.5 cm (1 in.) |
| Sensor Length | 25.4 cm (10 in.) |
| Weight | 0.27 kg (0.6 lb) |
Relative Humidity |
|
| Sensor | Vaisala’s HUMICAP H-chip |
| Measurement Range | 0.8% to 100% RH (non-condensing) |
| Output Signal Range | 0.008 to 1 Vdc |
| Accuracy at 20°C (against factory reference) | ±1% RH |
| Accuracy at 20°C (field-calibrated against references) |
|
| Temperature Dependence | ±0.05% RH/°C |
| Long-Term Stability | Typically, better than 1% RH per year |
| Response Time | 15 s with membrane filter (at 20°C, 90% response) |
| Settling Time | 500 ms |
Temperature |
|
| Temperature Sensor | 1000 ohm Platinum Resistance Thermometer |
| Measurement Range | -39.2° to +60°C |
| Output Signal Range | 0.008 to 1.0 V |
| Accuracy at -40°C | ±0.5°C |
| Accuracy at -20°C | ±0.4°C |
| Accuracy at 0°C | ±0.3°C |
| Accuracy at 20°C | ±0.2°C |
| Accuracy at 40°C | ±0.3°C |
| Accuracy at 60°C | ±0.4°C |
Please note: The following shows notable compatibility information. It is not a comprehensive list of all compatible products.
| Product | Compatible | Note |
|---|---|---|
| 21X (retired) | ||
| CR10 (retired) | ||
| CR10X (retired) | ||
| CR200X (retired) | ||
| CR206X (retired) | ||
| CR211X (retired) | ||
| CR216X (retired) | ||
| CR23X (retired) | ||
| CR295X (retired) | ||
| CR3000 (retired) | ||
| CR500 (retired) | ||
| CR5000 (retired) | ||
| CR510 (retired) | ||
| CR800 (retired) | ||
| CR850 (retired) | ||
| CR9000 (retired) |
The HMP45C should be housed in a 41003-5 10-plate naturally-aspirated solar radiation shield. The 27251 hex plug is required to mount the HMP45C in the 41003-5. At one time, this hex plug was shipped with the radiation shield but it no longer is. The41003-5 mounts to a tripod or tower mast, crossarm, or user-supplied pole.
HMP45C-L: 1
The HMP60 (with the Campbell Scientific cable) cannot be used with the 41003-5 10-Plate Radiation Shield without the use of additional hardware. For more information, refer to the Compatibility information on the HMP60 product page. The standard radiation shield for the HMP60 is the 41303-5A.